Kitronik

Sort By:  
  • Sewable Light Sensor with Battery Holder (KIT2721)

    This board allows LEDs to be turned on automatically when it is dark. On one side of the board is the coin cell holder, which takes a CR2032 coin cell as well as a small on/off slide switch. On the other side of the board is the light sensor. This design means that it is possible to cut a small hole in the front of the product for the light sensor to detect the light level, but be able to get to the back of the board to change the battery and turn the board off.

    When turned off,any connected LEDs will be off. When turned on the connected LEDs will be off in day light but come on in the dark. There are two sets of pads that can be used to connect LEDs to the board.

    The board measures 44 x 20 x 4.5 mm (excluding the light sensor, which is 2mm high).

    A PDF tutorial explaining how to use this board can be downloaded by clicking here
    Add to Cart
    £2.50
  • Sewable Push Button Switch (KIT2708)

    This sewable push switch can be used to activate your e-textiles project whilst it is pressed down (the circuit is broken as soon as pressure on the switch is released).

    It has two connection points to which the conductive thread is connected.The PCBs are double sided making the conductive thread connection very reliable (see example picture).

    Features:

    • Double Sided PCBs for reliable connections.
    • Clearly marked '+' and '-' connections.

    Contents:

    • 1 x Ultra Slim Push Switch.

    Dimensions:

    • Length: 18mm.
    • Width: 8.5mm.
    • Height: 3mm.
    Add to Cart
    £0.75
  • Sewable Conductive Thread, 6m (KIT2727)

    This is among the best conductive thread available. It is perfect for hand sewing and can be used on the bottom bobbin of a sewing machine (this will requite the thread to be wound on to the smaller bottom bobbin first).

    Approximately 6m of conductive thread.

    Conductive thread can be used like conventional sewing thread, however it electrically conducts allowing electronics to be integrated into textiles. This makes it ideal for use in a range of e-textile applications.

    Electrical Characteristics: The thread is nano-plated with silver to make it conductive. The conductive thread has a low resistance of approximately 40ohms per metre. This allows LEDs to be powered over quite large distances. Resistance does not vary significantly from one length of thread to the next, so you should be able to use this thread without concern for "dead" sections.

    Physical Characteristics: The conductive thread has a breaking strain of around 9.3 pounds (4.2 kilos). It comprises roughly 96 individual filaments, each coated with a micron-thick layer of natural silver. In construction, 16 of these filaments are wound together to form an initial twist; two of these twists are then twisted together, and finally three of these twists are combined to form the finished thread. The conductive thread is approximately 18 denier. It is heavier than a regular sewing thread, but not as heavy as an upholstery thread. It can be sewn on most domestic sewing machines using either a regular needle or the next size up. This thread does not fray.

    Key features:

    • No (or very low) fray.
    • Conductivity = approximately 40ohms per metre.
    • Count = 875 dTex.
    • Strength 3000 cN.
    • Elongation at break = 37%.
    • Twist = 240Z-380S.
    Add to Cart
    £2.50
  • Sewable Magnetic Switch (KIT2720)

    These sewable magnetic switches can be used to switch on LEDs when the magnet is placed near the switch. The magnet is included.

    It has two connection points to which the conductive thread is connected. The PCBs are double sided making the conductive thread connection very reliable (see example picture below).

    Features:

    • Double Sided PCBs for reliable connections.

    Contents:

    • 1 x Ultra Slim Magnetic Switch.

    Dimensions:

    • Length: 25mm.
    • Width: 6mm.
    • Height: 6mm.
    Add to Cart
    £3.40
  • Electro-Fashion Cat Kit (KIT2725)

    The 'Electro-Fashion Cat' is an ideal introduction to e-textiles. It should be possible for someone with basic sewing skills to make it successfully by following the instructions. When complete the cat's eyes will light up when the right ear is squeezed.

    This cat kit contains all the items you need to make the cat (except for a pair of scissors, a needle and pins for securing the felt when sewing).

    To make the cat the felt is cut into four pieces following the lines. The LED eyes, battery holder and switch are sewn on to a piece of felt following the stitch lines. Finally the cat is sewn together and stuffed with wadding. Pop the battery in and when the cat's ear is pressed the eyes will light.

    The kit contains:

    • 1x Printed felt
    • 2x sewable green slim LEDs
    • 1x sewable push button switch
    • 1x Sewable coin cell holder
    • 1x CR2032 coin cell
    • 2m conductive thread
    • 8m embroidery thread

    Resources:


    Caution: Please note this is not a toy.

    Add to Cart
    £15.00
  • Electro-Fashion Standard E-Textiles Pack (KIT2729)

    This pack is a great way to get started with E-Textiles.

    We have selected a number of products from our wearables range, including three of our ultra-slim LEDs and two separate power boards. There are enough components for you get started immediately to create some eye catching E-Textiles projects, the only limit is your imagination.

    Features:

    • Everything you need to complete two projects.
    • Enough Electro-Fashion components to get started immediately with E-Textiles.
    • Full instructions for assembly.
    • Great project ideas and tutorials.

    Contents:

    • 2 x Coin Cell Holder
    • 3 x Sewable LEDs (Blue)
    • 3 x Flashing LEDs (Blue)
    • 1 x Slide Switch
    • 1 x Push Switch
    • 2 x CR2032 Coin Cell Batteries
    • 1 x 6m Conductive Thread

    Dimensions:

    • Sewable Coin Cell Holder: 34 x 20 x 4.5mm (LxWxH)
    • Ultra Slim Sewable LED: 15 x 6.5 x 2.7mm (LxWxH)
    • Slide Switch: 18 x 8.5 x 4mm (LxWxH)
    • Push Button Switch: 18 x 8.5 x 3mm (LxWxH)
    • CR2032 Battery Height: 3.2mm, Diameter: 10mm.

    Requires:

    • Scissors.
    • Needles.

    Resources:

    Add to Cart
    £8.30
  • Electro-Fashion Deluxe E-Textiles Pack (KIT2728)

    This deluxe E-Textiles pack is a great way to get a little more involved with E-Textiles.

    We have selected a number of products from our Electro-Fashion range, including three of our ultra-slim LEDs and two seperate power boards. There are enough components for you get started immediately to create some eye catching E-Textiles projects, the only limit is your imagination.

    Features:

    • Everything you need to complete three projects.
    • Enough Electro-Fashion components to get started immediately with E-Textiles.
    • Full instructions for assembly.
    • Great project ideas and tutorials.

    Contents:

    • 2 x Sewable Blue LEDs.
    • 2 x Sewable White LEDs.
    • 2 x Sewable Sakuru (lilac) LEDs.
    • 2 x Blue Flashing LEDs.
    • 2 x Green Flashing LEDs.
    • 2 x White Flashing LEDs.
    • 1 x Slide Switch.
    • 1 x Push Switch.
    • 2 x CR2032 Coin Cell Batteries.
    • 1 x CR1220 Coin Cell Battery.
    • 1 x 6m Conductive Thread.
    • 1 x Coin Cell Holder.
    • 1 x Miniature Coin Cell Holder.
    • 1 x Switched Coin Cell Holder.

    Dimensions:

    • Ultra Slim Sewable LED: 15 x 6.5 x 2.7mm (LxWxH)
    • Slide Switch: 18 x 8.5 x 4mm (LxWxH)
    • Push Button Switch: 18 x 8.5 x 3mm (LxWxH)
    • CR1220 Battery: Height: 2mm, Diameter: 12mm
    • CR2032 Battery Height: 3.2mm, Diameter: 10mm
    • Sewable Coin Cell Holder: 34 x 20 x 4.5mm (LxWxH)
    • Sewable Miniature Coin Cell Holder: 22 x 12.5 x 4mm (LxWxH)
    • Switched Coin Cell Holder: 22 x 12.5 x 4mm (LxWxH)

    Requires:

    • Scissors.
    • Needles.

    Resources:

    Add to Cart
    £12.45
  • Sewable Slide Switch (KIT2709)

    This sewable two position miniature slide switch allows LEDs to be turned on or off in your e-textiles projects.

    It has two connection points to which the conductive thread is connected.The PCBs are double sided making the conductive thread connection very reliable (see example picture below).

    Features:

    • Double Sided PCBs for reliable connections.
    • Clearly marked '+' and '-' connections.

    Contents:

    • 1 x Ultra Slim Slide Switch.

    Dimensions:

    • Length: 18mm.
    • Width: 8.5mm.
    • Height: 4mm.
    Add to Cart
    £0.95
  • Electro-Fashion, LED Flasher Module Kit (KIT2719R)

    This unit provides a simple way of adding flashing white LEDs to a textiles project using conductive thread. The unit is programmed with a number of flashing patterns, which are selected by a push button on the main board. Pressing this button cycles through the following patterns: all LEDs constantly on, slow flash all, on all off, fast flash each in turn and turned off. The device features auto-off, which turns the unit off after 30 minutes to preserve battery life.

    This kit is supplied pre-built so requires no soldering. Each kit comprises three small PCBs. The largest of the three PCBs holds an LED plus the control electronics, battery and a push button. On both of the remaining PCBs there is an LED, these are connected to the main board with conductive thread (supplied).

    Depending upon flash pattern the battery lasts for approximately two days of constant use.

    Features:

    • Everything you need to complete one project.
    • Flasher control unit with 3 seperate modes.
    • Additional LEDs.
    • Full instructions for assembly.
    • Auto-Off to preserve battery life.

    Contents:

    • 1 x Flasher Control Board.
    • 2 x Sewable White LEDs.
    • 1 x CR2032 Coin Cell Batteries.
    • 1 x 2m Conductive Thread.

    Dimensions:

    • Flasher Control Unit Length: 34mm.
    • Flasher Control Unit Width: 20mm.
    • Flasher Control Unit Height: 9mm.
    • Ultra-slim LED Length: 15mm.
    • Ultra-slim LED Width: 6.5mm.
    • Ultra-slim LED Height: 2.7mm.
    • CR2032 Battery Height: 3.2mm.
    • CR2032 Battery Diameter: 10mm.

    Requires:

    • Scissors.
    • Needles.

    Resources:

    Add to Cart
    £6.80
  • CR2032 3V Coin Cell, Pack of 5 (KIT2262)
    This is a great value, high quality battery.
    Type: Lithium CR2032 coin cell.
    Voltage: 3V
    Capacity: 200mAh.
    Size: 20mm diameter, 3.2mm height.
    Pack size: strip of 5.
    Add to Cart
    £1.20
  • Sewable Flasher Controller, LEDs & Thread (KIT2719)

    This unit provides a simple way of adding flashing white LEDs to a textiles project using conductive thread. The unit is programmed with a number of flashing patterns, which are selected by a push button on the main board. Pressing this button cycles through the following patterns: all LEDs constantly on, slow flash all on all off, fast flash each in turn and turned off. The device features auto-off, which turns the unit off after 30 minutes to preserve battery life.

    This kit is supplied pre-built so requires no soldering. Each kit comprises three small PCBs. The largest of the three PCBs holds an LED plus the control electronics, battery and a push button. On both of the remaining PCBs there is an LED, these are connected to the main board with conductive thread (supplied).

    Depending upon flash pattern the battery lasts for approximately two days of constant use.

    Features:
    • Everything you need to complete one project.
    • Flasher control unit with 3 separate modes.
    • Additional LEDs.
    • Full instructions for assembly.
    • Auto-Off to preserve battery life.

    Contents:

    • 1 x Flasher Control Board.
    • 2 x Sewable White LEDs.
    • 1 x CR2032 Coin Cell Batteries.
    • 1 x 2m Conductive Thread.

    Dimensions:

    • Flasher Control Unit Length: 34mm.
    • Flasher Control Unit Width: 20mm.
    • Flasher Control Unit Height: 9mm.
    • Ultra-slim LED Length: 15mm.
    • Ultra-slim LED Width: 6.5mm.
    • Ultra-slim LED Height: 2.7mm.
    • CR2032 Battery Height: 3.2mm.
    • CR2032 Battery Diameter: 10mm.

    Requires:

    • Scissors.
    • Needles.

    Resources:

    Add to Cart
    £4.80
  • Sewable LED Board, Lilac (KIT2726)

    These ultra slim, pre-mounted e-textile LEDs run off a 3V coin cell battery and are illuminated continuously when powered.

    They have connections to which the conductive thread can be connected. These are clearly marked with '+' and '-' to indicate which is the positive and which is the negative connection.

    The PCBs are double sided making the conductive thread connection very reliable (see example picture below).

    Features:

    • Ultra Slim Sewable LEDs.
    • Double Sided PCBs for reliable connections.
    • Clearly marked '+' and '-' connections.
    • Individual LED (ready to use).

    Dimensions:

    • Length: 15mm.
    • Width: 6.5mm.
    • Height: 2.7mm.
    Add to Cart
    £0.65
  • Sewable LED Board, Green (KIT2723)

    These ultra slim, pre-mounted e-textile LEDs run off a 3V coin cell battery and are illuminated continuously when powered.

    They have connections to which the conductive thread can be connected. These are clearly marked with '+' and '-' to indicate which is the positive and which is the negative connection.

    The PCBs are double sided making the conductive thread connection very reliable (see example picture below).

    Features:

    • Ultra Slim Sewable LEDs.
    • Double Sided PCBs for reliable connections.
    • Clearly marked '+' and '-' connections.
    • Individual LED (ready to use).

    Dimensions:

    • Length: 15mm.
    • Width: 6.5mm.
    • Height: 2.7mm.
    Add to Cart
    £0.65
  • Sewable LED Board, White (KIT2714)

    These ultra slim, pre-mounted e-textile LEDs run off a 3V coin cell battery and are illuminated continuously when powered.

    They have connections to which the conductive thread can be connected. These are clearly marked with '+' and '-' to indicate which is the positive and which is the negative connection.

    The PCBs are double sided making the conductive thread connection very reliable (see example picture below).

    Features:

    • Ultra Slim Sewable LEDs.
    • Double Sided PCBs for reliable connections.
    • Clearly marked '+' and '-' connections.
    • Individual LED (ready to use).

    Dimensions:

    • Length: 15mm.
    • Width: 6.5mm.
    • Height: 2.7mm.
    Add to Cart
    £0.65
  • Sewable LED Board, Blue (KIT2713)

    These ultra slim, pre-mounted e-textile LEDs run off a 3V coin cell battery and are illuminated continuously when powered.

    They have connections to which the conductive thread can be connected. These are clearly marked with '+' and '-' to indicate which is the positive and which is the negative connection.

    The PCBs are double sided making the conductive thread connection very reliable (see example picture below).

    Features:

    • Ultra Slim Sewable LEDs.
    • Double Sided PCBs for reliable connections.
    • Clearly marked '+' and '-' connections.
    • Individual LED (ready to use).

    Dimensions:

    • Length: 15mm.
    • Width: 6.5mm.
    • Height: 2.7mm.
    Add to Cart
    £0.65
  • Sewable LED Board, Red (KIT2712)

    These ultra slim, pre-mounted e-textile LEDs run off a 3V coin cell battery and are illuminated continuously when powered.

    They have connections to which the conductive thread can be connected. These are clearly marked with '+' and '-' to indicate which is the positive and which is the negative connection.

    The PCBs are double sided making the conductive thread connection very reliable (see example picture below).

    Features:

    • Ultra Slim Sewable LEDs.
    • Double Sided PCBs for reliable connections.
    • Clearly marked '+' and '-' connections.
    • Individual LED (ready to use).

    Dimensions:

    • Length: 15mm.
    • Width: 6.5mm.
    • Height: 2.7mm.
    Add to Cart
    £0.65
  • Sewable Switched Coin Cell Holder (KIT2711)

    This specially designed e-textiles coin cell holder has large connection points for the conductive thread.

    These are clearly marked to show the battery polarity. The unit also has a small power switch so that you can turn the power on and off.

    It uses a very thin PCB material to keep its size to a minimum.This allows it to be easily incorporated into your own e-textiles designs.

    Caution: This coin cell holder contains Nickel and should not be used in designs where it will be in prolonged contact with the skin.

    The board accepts CR2032 batteries.

    Dimensions: L44 x W20 x H4.5mm

    Add to Cart
    £1.85
  • Sewable Tilt Switch (KIT2710)

    This sewable tilt switches can be used to activate your e-textiles project when it is tilted.

    When horizontal this switch is off. When tilted 10º from horizontal the tilt switch is on.

    It has two connection points to which the conductive thread is connected. The PCBs are double sided making the conductive thread connection very reliable (see example picture below).

    Features:

    • Double Sided PCBs for reliable connections.

    Contents:

    • 1 x Sewable Tilt Switch.

    Dimensions:

    • Length: 26mm.
    • Width: 6.5mm.
    • Height: 7mm.
    Add to Cart
    £1.05
  • Sewable Coin Cell Holder (KIT2701)

    This specially designed e-textile coin cell holder has large connection points for the conductive thread.

    These are clearly marked to show the battery polarity. It is also uses a very thin PCB material to keep it's size to a minimum.

    This allows it to be incorporated into your own e-textiles designs.

    Caution: This coin cell holder contains Nickel and should not be used in designs where it will be in prolonged contact with the skin.

    The board accepts CR2032 batteries.

    Dimensions: L34 x W20 x H4.5mm.

    Add to Cart
    £1.10
Per Page      1 - 19 of 19

Powered by Abantecart eCommerce Solution